Candy TR 31 RUFA User Manual download pdf (Page 9)

INSTALLING A DOMESTIC APPLIANCE CAN BE A COMPLICATED OPERATION WHICH IF NOT CARRIED OUT CORRECTLY, CAN SERIOUSLY

AFFECT CONSUMER SAFETY. IT IS FOR THIS REASON THAT THE TASK SHOULD BE UNDERTAKEN BY A PROFESSIONALLY QUALIFIED

PERSON WHO WILL CARRY IT OUT IN ACCORDANCE WITH THE TECHNICAL REGULATIONS IN FORCE. IN THE EVENT THAT THIS ADVICE

IS IGNORED AND THE INSTALLATION IS CARRIED OUT BY AN UNQUALIFIED PERSON, THE MANUFACTURER DECLINES ALL RESPONSIBILITY

FOR ANY TECHNICAL FAILURE OF THE PRODUCT WHETHER OR NOT IT RESULTS IN DAMAGE TO GOODS OR INJURY TO INDIVIDUALS.

8 GB

This appliance is not connected to an evacuation device for the

products of combustion. It must be installed and connected in

compliance with the norms in force in the country of installation.

Particular attention should be given to the availability of ventilation.

The turnover of air necessary for combustion is a minimum of 2

m3/h per kW of power.

Gas connection should be carried out in compliance with the

norms in force in the country of installation.

A stop tap, a regulator valve or a release valve for propane gas,

should be fitted to the gas supply pipe. Use only taps, regulator

valves, connectors and flexible hoses with the official mark of

approval of the country of installation.

Le raccordement gaz doit être effectué conformément aux

règlements en vigueur dans le pays d'installation.

2 POSSIBLES MEANS OF CONNECTION :

• CONNECTION BY RIGID PIPE

Connect directly to the threaded end of the inlet pipe.

• CONNECTION BY FLEXIBLE PIPE WITH MECHANICAL

CONNECTOR

(We recommend this type of connection)

Screw the nuts of the flexible pipe directly on to the inlet pipe

at one end and the gas supply stop tap at the other.

GAS CONNECTION

BUILDING-IN

BUILDING-IN : both the worktop where the hob will be fitted and

any adjacent kitchen furniture must be made from heat resistant

material and fixed with heat resistant adhesive.

If, when installing the hob, the lower hob face is adjacent to an

area normally accessible when handling or cleaning, fit a heatproof

partition 1 cm below the base of the hob with a 10X10 cm opening

at the rear right-hand corner, to avoid any risk of scorching or

damage.

A foam adhesive is supplied with the hob. Stick this seal under

the edge of the body as near as possible to the outer edge of the

hob. Press round the edges of the hob, so that the seal flattens

out and ensures an air tight seal.

Warning : at the rear of the appliance, take care not to block the

air inlets necessary for combustion to take place.

The body of the hob is fitted with 4 location holes to take the fixing

brackets that secure the the hob in the unit. Place the 4 fixing

brackets in such a way that the hob is placed perfectly in the

support unit.

INSTALLATION

N.B.: carry out a final check for leaks on the pipework using a

soapy solution. Never use a flame. Also, make sure that the

flexible pipe cannot come into contact with a moving part of the

cabinet (eg, a drawer) and that it is not situated where it could

be damaged.

min 10 mm

Sp da 25 a 45 mm

Accessible

space

SEAL

Not cooled

oven

ELECTRICAL CONNECTION

Warning : before proceeding with the connection, check the

continuity of the earthing of the power supply unit.

We cannot be held responsible for any accident which has

resulting from the use of an appliance which is not connected

to earth, or whose earthing is defective.

The mains electricity supply connected to the appliance should

comply with the norms in force in the country of installation.

Connection to the mains electricity supply should be through a

socket with an earth terminal, or through an intermediary switching

device with a gap between contacts of at least 3 mm.

The power supply unit must be protected by appropriate fuses

and use cables of a large enough cross section to provide a normal

supply to the appliance.

The hob is fitted with a power supply cable* with plug which allow

it to be connected only to a power supply of 230 V between phases,

or between phase and neutral.

Connect to a 10/16 Amp socket. Before connecting, it is

compulsory to check :

• the power supply voltage shown on the electricity meter,

• the adjustment of the circuit breaker, and

• the fuse rating,

• the earth continuity.

Note : the socket must be reachable for any eventual repair.

Take care of its location at the time you install the hob.

* The eventual replacement of the supplying cord must be carried

on by the After Sales Service or by an agreed engineer, with a

cord whose characteristics must be similar to the original one :

• Gas hob : cord type H05RR-F, H05VV-F, H05V2V2-F (3 x 0,75

2 section),

• Mixed hob : cord type H05RR-F, H05VV-F, H05V2V2-F (3 x 1,5

mm2 section).

CYLINDRICAL

CONICAL

Not cooled

oven

For some models a conic link is furnished to outfit for the installation

in the countries where this type of link is obligatory; in the following

figures it is pointed out how to recognize the different types of

links. In every case the cylindrical part of the link has to be

connected to the hob.

min 70 cm

min 15 cm

min 5,5 cm

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 25 26

Comments to this Manuals

No comments

Candy TR 31 RUFA User Manual Page 9

Comments to this Manuals

Related products and manuals for Stoves Candy TR 31 RUFA