Candy CD 571 S NORD User Manual download pdf (Page 43)

The filter D must be inserted between the tap B and the inlet hose A, remembering

to fit the washer C.

If the dishwasher is connected to new pipes or to pipes which have not been in use

for a long time run water through for a few minutes before connecting the inlet hose.

In this way no deposits of sand or rust will clog up the water inflow filter.

Connecting the outlet hose

The outlet hose should disharge into a standpipe, making sure that there are no kinks

(fig. 4).

The standpipe must be at least than 40 cm above floor level and it must have an

internal diameter of at least 4 cm. It is advisable to fit an anti-odour air trap (fig. 4 x).

If necessary the outlet hose can be extended up to 2,6 m, provided that it is kept at

a maximum height of 85 cm above floor level.

The hose can be hooked over the side of the sink (it must not be immersed in water,

in order to prevent water from being syphoned back to the machine when this is in

operation) (fig. 4 y).

When installing the appliance under a worktop the hose pipe clamp must be attached

to the wall in the highest possible position under the worktop (fig. 4 z).

Check that there are no kinks in the inlet and outlet hoses.

123

Water connection

The inlet and drain hoses can be directed to left or right.

The dishwasher can be connected to either cold or hot water, as long as it is

no hotter than 60 °C.

Water pressure must be between 0,08 MPa and 0,8 MPa. If the pressure is below

the minimum consult our service department for advice.

The inlet hose must be connected to a tap so that the water supply can be cut off

when the machine is not in use (fig.1 B).

The dishwasher is fitted with 3/4" threaded connector (fig. 2).

Connect inlet hose A to water tap B with a 3/4" attachment making sure that it has

been properly tightened.

If it is necessary to lengthen the inlet pipe, an extension pipe can be fitted.

If limescale deposits or sand are present in the water, it is advisable to obtain the

appropriate filter, art. 9226085, from the Service Centre (fig. 3).

INSTALLATION (Technical notes)

After unpacking, adjust the height of the dishwasher.

For the dishwasher to work correctly it must be level.

Adjust the feet so that the machine does not tilt by more

than 2 degrees. If it you need to move the machine after

removing the packaging, do not try to lift it by the bottom

of the door. Follow the instructions in figure. Open the

door slightly and lift the machine by holding on the top.

Important: when the appliance is located on a

carpet floor, attention must be paid to ensure that

there is no obstruction to the bottom vents.

Make sure that the plug on the appliance remains

accessible after installation.

This appliance complies with Directives

89/336/EEC, 73/23/EEC and following changes.

Electrical connection (230 V)

This appliance complies with all the international safety standards and is fitted with a

3 pin plug with earth connection to ensure complete earthing of the product.

In the absence of adequate earthing you will notice that when touching the metal

parts of your appliance an electrical dispersion can be felt due to the presence of a

radio interference suppressor.

Before connecting the appliance to the mains supply it is important to ensure:

– That the supply socket is properly earthed.

– That your electricity supply is capable of meeting the consumption requirements

listed on the rating plate of your appliance.

Important: manufacturer declines all responsibility for any damages due to

nonearthing of the machine.

1 2 ... 38 39 40 41 42 43 44 45 46 47 48 ... 52 53

Comments to this Manuals

No comments

Candy CD 571 S NORD User Manual Page 43

Comments to this Manuals

Related products and manuals for Dishwashers Candy CD 571 S NORD