Candy TRIO 9503 X User Manual download pdf (Page 9)

USE THE DISHWASHER

8 GB

DISHWASHER CONTROLS

A Programme selection indicator lights

B Programme selection button

C Programme description

D On/off button

SELECTING THE PROGRAMMES AND SPECIAL FUNCTIONS

The dishwasher and the oven cannot be used simultaneously.

Setting a programme

Open the door and press the On/off button ; the 4 Program selection LEDs start flashing.

- Set the required programme by pressing Programme selection button, LED of the chosen programme will turn on (2 LEDs for COLD

RINSE programme).

- Close the door (after audible signal), the chosen programme will start automatically.

Opening the door

Grip the handle in the front panel and pull forward. If the machine

comes open while it is working, an electrical safety device

automatically switches everything off. For the machine to work

properly, the door should not be opened while it is in operation.

Closing the door

Place the basket in the dishwasher. Make sure that the spray arm

is free to rotate and is not obstructed by cutlery, crockery or pans.

Close the door, pressing on it to make sure it is firmly shut.

Interrupting a programme

lt is not recommended that the door be opened while a programme

is running, and especially not during the main wash phase and

final drying.

However, the appliance stops automatically when the door is

opened.

When the door is closed again, the programme continues

automatically.

If you wish to change or cancel a programme that is running, carry

out the following procedure:

. open the door, keeping the Programme selection button "P"

pressed in until all 4 indicator lights are flashing. The current

programme is cancelled. A new setting can now be made.

Before starting a new programme, you should check that there is

still detergent in the dispenser. If necessary, top up the dispenser.

WARNING: if the door is opened during the drying phase, an

intermittent audible signal is activated to advise that the cycle is

not yet completed.

End of programme

The end of the programme is indicated by an audible signal. When

the door is opened the programme selection indicator lights start

flashing. Release the On/off button.

Deactivating the audible signal

The audible function can be deactivated in the following way:

- press the On / Off button

- wait till the programme LEDs blink

- within 2 minutes, press and keep pressed for at least 30 seconds

the Programme Selection button (the programme LEDs will still

blink and an intermittent audible signal is heard).

- Once the first two LEDs on the left are illuminated without blinking

and the audible signal is off, release the button (the audible

signal function is active).

- Press again the Programme Selection button, the first two LEDs

on the left will go off and the other two LEDs will turn on (the

audible signal function is deactivated)

- An audible signal will confirm that the setting is completed

- To set again the audible signal function repeat the whole

procedure.

USE THE DISHWASHER

Fault Signals

If malfunctions or faults occur when a program is running, the

LED that corresponds to the selected cycle (2 LEDS for COLD

RINSE programme) will blink rapidly and an audible signal will be

activated.

In this case, turn the dishwasher off by pressing the On / Off

button. After checking to make sure the water inlet hose tap is

open, that the drain hose is not bent and that the siphon or filters

are not clogged, re-start the selected program. If the anomaly

persists, contact Customer Service.

Important !

To ensure the correct operation of the anti-overflow safety

device, it is recommended not to move or to tilt the dishwasher

during operation.

If it is necessary to move or to tilt the dishwaher, first make

sure the washing cycle is finished and that no water is left

in the tank.

Attention - The dishwasher is equipped with an anti-overflow

safety device which in the event of anomaly intervenes by

evacuating water in excess.

The filtering system is composed

of :

- a central filter cup which traps the

largest food particles.

- a flat filter which continuously filters

the washing water.

- the micro filter, situated under the

flat filter, which traps the smallest food particles ensuring a perfect

rinse.

For best results, the filter unit should be checked and cleaned

after each wash.

To remove the filter unit, simply grip the handle and lift the whole

unit out.

The central cup is just resting on top for easy cleaning.

The dishwasher is fitted with a self cleaning micro filter, which

only requires checking about once every 15 days.

However, it is advisable to check after every wash, that the central

cup and the flat filter are not clogged.

NB : After cleaning the filters, make sure that they are correctly

reassembled, one inside the other, and that the flat filter is properly

positioned at the bottom of the dishwasher.

A poor seating of the filter unit could have an adverse effect on

the efficiency of the appliance.

Important : Never use the dishwasher without filter.

PRELIMINARY OPERATIONS AND CLEANING

THE FILTER UNIT

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 79 80

Comments to this Manuals

No comments

Candy TRIO 9503 X User Manual Page 9

Comments to this Manuals

Related products and manuals for Stoves Candy TRIO 9503 X