Candy CMD 94 X User Manual download pdf (Page 3)

blinking, the anti-grease filters must be cleaned and the charcoal filters replaced (120 hours of operation). Obviously, if the

hood is not a filtering model and does not have a charcoal filter , clean the anti-grease filters both when the central segment

goes on and when it starts blinking. The filter alarm can be seen when the motor is off and for about 30 seconds. To reset

the hour counter, keep the button pressed for 2 seconds while the alarm can be seen.

Commands shown in Fig. 17: Button A = light button. Button B = first speed motor ON/OFF button. Button C = second

speed button. Button D = third speed button. E = motor on light.

Commands shown in Fig. 18: Button A: turns the lights on/off; every 30 hours of operation the corresponding pilot lamp

(S) comes on to indicate that the anti-grease filters must be cleaned; every 120 hours of operation the corresponding pilot

lamp (S) flashes to indicate that the anti-grease filters must be cleaned and the charcoal filter replaced. To restart the hour

counter (RESET), hold the button A pressed down for about 1” (while the pilot lamp S is on). Button B: drives the motor

in first speed (the corresponding pilot lamp comes on); when holding it down for about 1”, the motor cuts out. Button C:

drives the motor in second speed (the corresponding pilot lamp comes on); when pressing the button a second time (while

the pilot lamp is on) , the TIMER is activated and thus the motor stops after 5’ (the pilot lamp flashes). Button D: drives

the motor in third speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot

lamp is on) , the TIMER is activated and thus the motor stops after 5’ (the pilot lamp flashes). Button E: drives the motor

in fourth speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp is

on) , the TIMER is activated and thus the motor stops after 5’ (the pilot lamp flashes).

Pay special attention to the anti-grease filters:

if the model purchased has the commands shown in Figure 16: the anti-

grease filters must be cleaned approximately once every 30 hours of operation (when the central segment on the display

goes on or starts blinking). To remove the filters: press inward on the clamps at the handles and pull the filter downward.

Wash out the filter by hand or in the dishwasher using a neutral soap. Once the cleaned filters are reinstalled, keep button

R (Reset) pressed for two seconds to reset the counter. For further information, see the Commands in Fig. 16 in the

paragraph entitled “Operation”.

If the model purchased has the commands shown in Figure 17: the grease filter must be

replaced periodically: exactly how often depends on use (at least once every other month). To remove the filter: push inward

on the clamp at the handle and pull the filter downward. Wash out the filter by hand or in the dishwasher using a neutral

soap.

If the model purchased has the commands shown in Figure 18: the anti-grease filters must be cleaned approximately

once every 30 hours of operation (when the light button lamp comes on) - Fig. 18S). To remove the filters: press inward

on the clamps at the handles and pull the filter downward. Wash out the filter by hand or in the dishwasher using a neutral

soap. Once the cleaned filters are reinstalled, to reset the counter hold the light button pressed down for about 1” (Fig.18A)

while the corresponding pilot lamp (S) is on. For further information, see the Commands in Fig. 18 in the paragraph entitled

“Operation”.

Replacing the charcoal filters: If the unit is a filtering hood, the charcoal filters must be replaced: to remove them press

inward on the clamp (Fig. 15) and rotate the filter downward until the 2 tabs can be removed from the housing.

If the model purchased has the commands shown in Figure 16, the charcoal filters must be replaced whenever the central

segment of the display starts blinking (i.e. every 120 hours of operation). If the model purchased has the commands shown

in Figure 17, the charcoal filters must be replaced according to use: on average once every 6 months. If the model

purchased has the commands shown in Figure 18, the charcoal filters must be replaced each time the light button (Fig.18S)

lamp flashes (i.e. every 120 hours of operation).

Lighting: Depending on the model purchased, see Fig.19 or Fig. 20.

Fig. 19: to remove the halogen lamps, turn the locknut counter-clockwise. Replace with the same type of lamp.

Fig. 20: if your appliance has the same kind of lights as in the figure 20, to replace the incandescent light bulbs remove

the anti-grease filters and remove it; replace with light bulbs of the same type.

DEUTSCH

BESCHREIBUNG

Das Gerät kann in Filterversion, in Aspirationsversion und in der Version mit externem Motor geliefert werden.

In der

Filterversion (Abb. 1) werden die durch das Gerät geleitete Luft und der Dampf durch Kohlefilter gereinigt und dann über

die seitlichen Lüftungsgitter der Haube wieder in Zirkulation gebracht. ACHTUNG! Beim Einsatz der Filterversion müssen

die Kohlefilter zusammen mit einem Luftablenker eingesetzt werden, der in den oberen Rohrabschnitt montiert wird und

die Rezirkulation der Luft und Ableitung in die Umgebung ermöglicht (Abb. 1A).

In der Aspirationsversion (Abb. 2)

werden die Dämpfe und Küchengerüche direkt über eine Evakuationsöfffnung in der Wand oder Decke nach außen

a/jointfilesconvert/1335466/bgezogen. Daher sind keine Kohlefilter notwendig. In der Version mit externem Motor (Abb. 3) ist das Gerät mit einer

Aspirationszentrale zu verbinden, die getrennt arbeitet und das Gerät als Verbindungsbasis für die abzuleitende Luft

benutzt. Bitte verwenden Sie nur eine der im Originalkatalog vorgeschlagenen Zentralen.

INSTALLATION

Vor den Montageoperationen muß/müssen zur leichteren Handhabung des Geräts der/die Antifettfilter entfernt werden:

Den Festhalter in der Nähe des Griffs nach innen drücken und den Filter nach unten ziehen (Abb. 4).

Befestigung an der Wand (Abb. 5): Bohren Sie mit der mitgelieferten Bohrschablone die Löcher an den jeweiligen Stellen

an der Wand. Wie bereits im Kapitel “Montage und Gebrauchsanweisung” beschrieben ist darauf zu achten, daß der

Abstand zwischen dem unteren Rand der Haube und der Kochfläche mindestens 650 mm beträgt. Den Metallbügel (B)

1 2 3 4 5 6 7 8 ... 19 20

Comments to this Manuals

No comments

Candy CMD 94 X User Manual Page 3

Comments to this Manuals

Related products and manuals for Hoods Candy CMD 94 X